Carryme DC Electric Folding Bike - DIY 電動Carryme Bike摺疊自行車

DIY ELECTRIC CARRYME FOLDING BIKE - 13KG (CARRYME 電動摺疊車 13KG) 原廠 DS 雙速CarryMe 重量是 8.8kg, 經過改裝電動後重量為 13kg (不連鋰電池2.2kg)

http://diy-electric-carryme-bike.blogspot.com/2012/04/diy-electric-carryme-folding-bike-13kg.html

SWITCH ON/OFF - MOUNTING DESIGN ELECTRIC DS CARRYME FOLDING BIKE - 電動CARRYME DS FOLDING DIY DC ELECTRIC CARRYME BIKE - 展開電動CARRYME摺疊自行車 - 視頻. .... 開關制支架�...

http://diy-electric-carryme-bike.blogspot.com/2012/04/switch-onoff-electric-ds-carryme.html

COMPLETED DIY ELECTRIC CARRYME FOLDING BIKE - 完成改裝電動CARRYME

http://diy-electric-carryme-bike.blogspot.com/2012/04/completed-diy-electric-carryme-folding.html

ELECTRIC CARRYME FOLDING BIKE (CONTROLLER INSTALLATION) - DIY 電子部分組裝

http://diy-electric-carryme-bike.blogspot.com/2012/04/electric-carryme-folding-bike.html

ELECTRIC CARRYME FOLDING BIKE - LITHIUM BATTERY 鋰電池座 定出車尾主架上原有的2個貨架孔位置. 再把鋰電座上的孔對位定出鑽孔位於. ...

http://diy-electric-carryme-bike.blogspot.com/2012/04/electric-carryme-folding-bike-lithium.html

DIY ELECTRIC CARRYME FOLDING BIKE - 馬達支撐架安裝...... 測試24V : 250W 有刷馬達轉動順暢度..............

http://diy-electric-carryme-bike.blogspot.com/2012/04/diy-electric-carryme-folding-bike.html

INSTALLATION OF REAR FLYWHEEL CONNECTOR - 組裝後輪飛輪連接器 完成車制後輪飛輪連接器飛後, 放在後輪呔上訂下要鑽孔的位置 確定位置是否正確 �...

http://diy-electric-carryme-bike.blogspot.com/2012/04/installation-of-rear-flywheel-connector.html

雙速Carryme 後輪拆解 - Carryme Folding Bike (Rear Wheel Deassembly) 拆除後輪左右兩個大六角帽 之後可以拆去後車軸拉力杆鑼絲 之後可以放鬆鏈條 ...

http://diy-electric-carryme-bike.blogspot.com/2012/04/carryme-carryme-folding-bike-rear-wheel.html

DC Electric CarryMe Folding Bike - 馬達支撐設計過程. 電腦畫出3D 設計圖後. 3mm厚鐡片長製出展平圖樣. 用printer 打印一張圖樣後,貼上在鐡板後�...

http://diy-electric-carryme-bike.blogspot.com/2012/04/dc-electric-carryme-folding-bike_14.html

DC ELECTRIC CARRYME FOLDING BIKE - FLYWHEEL 設計過程. 電腦畫出3D 設計圖後. 用我的Reprap "Prusa" 3D Printer 來打印出零件來觀察及試位. 用ABS 膠料來打印�...

http://diy-electric-carryme-bike.blogspot.com/2012/04/dc-electric-carryme-folding-bike.html

雙速CARRYME 前輪拆解 - CARRYME FOLDING BIKE (FRONT WHEEL DEASSEMBLY)

http://diy-electric-carryme-bike.blogspot.com/2012/04/carryme-carryme-folding-bike-front.html

小改 CARRYME 附助小輪. 在網上看到一些專門用在Carryme改小輪, 但售價都不便而, 因此在五金店買了一對帶有 608軸承的小輪. 但由於Carryme 原來所支...

http://diy-electric-carryme-bike.blogspot.com/2012/04/carryme.html

參考了原廠PACIFIC-CYCLES的設定,定出了初步馬達的裝設位置. 原廠無刷馬達尺寸比較細, 因此放置位置可以靈活一點. 我發現我的雙速Carryme 與...

http://diy-electric-carryme-bike.blogspot.com/2012/04/dc-electric-carryme-folding-bike-3d.html