Probably failed usb connector on the unit.
https://community.emlid.com/t/rx-update-connection-problem/37857#post_21
Okay, thanks for the update. Fingers crossed.
https://community.emlid.com/t/rx-update-connection-problem/37857#post_20
Not yet. Waiting on my dealer to send me another one under warranty and see if that resolves it.
https://community.emlid.com/t/rx-update-connection-problem/37857#post_19
Was there a resolution to this?
https://community.emlid.com/t/rx-update-connection-problem/37857#post_18
Agreed. Great suggestion. Let’s get it implemented.
https://community.emlid.com/t/feature-suggestion-emlid-studio-processing-report/38017#post_4
It should always be ARP. The Rinex file should contain your antenna phase center offset.
In fairness it was, both parties did all the right things. Something changed and got out of sync.
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_16
I ran a PPK project using 2 Leica antenna. I uploaded both rover and base, Emlid Studios said it recognized the antenna type and would apply the correct offsets. Everything seems fine. Good fixed...
What gets me, is why is this not being tested before release… not to mention 2 parties at that… and 2 different OS versions also?
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_15
It’s been the same situation with Field Genius Android. Unfortunately some confusion with the IMU interfacing strategy and both drivers likely operate under the same assumptions. The good news ...
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_14
: / Emlid Flow Survey gone! Emlid Flow & Emlid Flow 360 > I am currently working in the field and have VERY limited time. > Currently utilizing a Samsung Galaxy Tab Acti...
https://community.emlid.com/t/emlid-flow-lost-all-my-projects-twice/38078#post_2
App version 10.4 I just finished a survey and when I got home and opened the app, there are NO projects listed in “Survey” section. I had several projects in there and now they are all gone...
https://community.emlid.com/t/emlid-flow-lost-all-my-projects-twice/38078#post_1
ruth.bongon: > I understand what you mean. I’ve reported this to the developers, > and they suggested a workaround: copy the angle with three decimal > places, and i...
Long story short, FG and FGA aren’t compensating for tilt right now. MS has indicated that they are very motivated to get it to work, so hopefully the issues they have seen will all be resolved...
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_13
Hi ruth.bongon i cant use one of the points form the corrected CSV. Those points are from my rover. Emlid Studio I upload the rover Rinex file to rover tab Base Rinex to the base tab Rinex fil...
Hi @rpekelder , I am not familiar with this kind of integration, so I can hardly suggest anything. But I found this old thread that can be of help?
https://community.emlid.com/t/emlid-rs2-with-agleader-display/37958#post_3
So what was the outcome @merryna.anggriani ? Can the RINEX log files from BOTH the ROVER and BASE be used to restore the measured points even if CSV file not available from Flow since Flow pro...
https://community.emlid.com/t/emlid-flow-survey-gone/38047#post_8
Hi @chavezindalecio , Will you use one of the points from the corrected CSV as the base coordinates? If so, could you please give me a walkthrough on how you post-process your data with Stop an...
Hi @1573barbaglinicola , I understand what you mean. I’ve reported this to the developers, and they suggested a workaround: copy the angle with three decimal places, and it should work.
I’ve been playing around with this and I don’t see a way where it could be user error. Either/both a mistake by MS or Emlid. Working on it.
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_11
Microsurvey FieldGenius How To: Turning Tilt Sensor On and Off | Bench Mark
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_10
Similiar to here MicroSurvey FieldGenius How To: Taking a Tilt Offset Measurement | Bench Mark
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_9
Go to measure modes and collect a tilt shot , it looks like you are in std measure mode
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_8
I was actually mistaken, Ruth is right, E/N/U disappears when we reprocess with Stop&Go. I was mixed up because we were mixing RTK and PPK in our project.
Hi guys, Thanks for the meaningful conversation! It’s a totally fine option to work in a base+rover setup using Reach M2 and Reach RS2. As Adrian also mentioned, a difference between the un...
https://community.emlid.com/t/reach-m2-setup-in-emlid-flow/37838#post_15
If it’s the obvious one accessed by touching the tilt bubble level on the right panel then that one is turned on.
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_7
Is there maybe a setting that needs to be turned on for tilt
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_6
I’m just getting setup. I’m new to tilt receivers. I tested my RS3 against a known point with both FG and Flow using a SmartNet fix. My vertical is always higher than it should be, and when t...
https://community.emlid.com/t/microsurvey-fieldgenius-12-rs3-driver-release/37668#post_5
Hi Luis, > I have an AUTEL EVO II PRO RTK drone and indeed, the precisions are > not saved in XMP metadata. I see. For now, the XMP support in Emlid Studio 1.8 is for DJI dr...
https://community.emlid.com/t/ppk-horizontal-and-vertical-accuracy-on-exif-jpg/38001#post_7